Building tower clock building clock building clock installation specification and precautions 2
Whether the tower clock can operate normally is not only related to the quality of the tower clock equipment, but also has a great relationship with the installation quality. The following are the simple installation standards and precautions of our company:
4. Cautions for installation of movement and feedback switch
a. Ensure that the movement shaft is in the center of the clock face, and the movement shaft is perpendicular to the clock face.
b. Make sure that when the movement, the sub-axis exceeds the clock face by an appropriate length, and the distance between each face is equal.
c. It is firmly connected with the clock face and other parts to ensure that the movement does not vibrate when it is running.
d. There is enough space in the position of the movement to ensure the smooth disassembly of the movement during maintenance.
e. Check whether the movement of the movement is flexible, whether there is no movement or great resistance to the hand, and whether there is oil leakage, and then check whether the stepping motor and the movement are firmly fixed, and no looseness is allowed.
f. Pay attention to the wiring method of the six-core wire connected to the stepper motor. Every two of the stepper motor is one color, and there are three colors in total. When connecting with the sheathed wire driver board, the longer motor wire of the same color of the stepping motor should be connected first, and the shorter one should be connected later. The order of connecting the six-core sheathed wire is red and yellow. , green, blue, black, white.
g. When installing the feedback switch, pay attention that the gap between it and the shaft is less than 2mm. And be sure to fasten the fastening nut of the feedback switch, and it is not allowed to fasten the nut with other fillers. At the same time, it is also necessary to observe whether the light-emitting tube on the feedback switch flashes regularly during operation, otherwise it must be detected whether the feedback switch has a working voltage of 24
5 Precautions for installation of timekeeping system
a. The horn is facing the audience, and the bell mouth should be kept in a posture of looking down at 10-15 degrees. It is strictly forbidden for the bell mouth to face the sky, so as to avoid rainwater burning the voice coil.
b. Evenly distributed or according to customer requirements.
c. Five obstacles ahead.
d. The screws between the speaker bracket and the speaker are fastened, and the speaker bracket and the support are firmly fixed.
e. When connecting the speakers in parallel, pay attention to the connection of the same color wires, and distinguish the positive and negative poles.
f. The connecting wire of the amplifier and the speaker must use a wire with a cross-section of more than 1.5 square mm
g. After the speakers are installed, use a multimeter to measure the resistance of 8 speakers in parallel, and the resistance is about 2 ohms. Otherwise, check the quality of each speaker one by one.
h. The volume switch potentiometer of the amplifier should be opened to 2/3 of the knob, and it is not necessary to open it to prevent the speaker from being burned.
i. The output voltage of the amplifier is about 39 volts when it is no-load.
6. Precautions for installation of tower clock control system
a The reliable distance of the control system from the movement and the horn is within 50 meters.
b Place it in a ventilated and dry place, the temperature in the city should be between 0 and 40 degrees, especially pay attention to the severe cold in the northeast and the humidity in the south.
c Pay attention to dust prevention and a large amount of dust intrusion.
d. Party A is required to have a special person responsible for custody, and to train the special person assigned by Party A to care and debug.
e To find out the safety and reliability of the 220v power cord entering the house, the cross section of the power cord shall not be less than 1.5 square mm.
f To detect the electricity voltage of the tower clock, it is required to be between 200 and 240 volts, especially when the voltage value after 20 o'clock exceeds the range, a regulated power supply of more than 3kva should be added.
g. Pay attention to the safety measures of preventing rain, fire, low temperature and strong magnetic field in the control system environment. The control system should be installed in a clean and tidy room without inflammables and substation systems around. Otherwise, shielding measures should be taken to prevent strong magnetic fields. Interference to the system, the ambient temperature of the master clock is 0-45 degrees, and the ambient temperature of the sub-clock is -10 to plus 50 degrees, so pay attention to the local temperature during installation, and take certain insulation measures to prevent the control system from running out of control.
h Before the installation of the control system, check all the circuit boards in the control cabinet and the connecting lines of each part to check whether they are loose and unsoldered, so as to eliminate the poor contact caused by vibration during transportation, which will cause the system to be abnormal.
i After the control system is checked, power on the test without load to verify whether the system is running normally, including the display status of the display screen and whether the output voltage of the driver board is around volts. Immediately turn off the power and troubleshoot the fault. It is strictly forbidden to plug and unplug the circuit board with power on.
After 15 minutes of no-load operation, if there is no fault, turn off the power supply, connect the movement control line, and start debugging.





